3DxWare 10 Beta Feedback

[Fred]

Try the instructions from this post.
viewtopic.php?t=4901

This isnt the solution just a patch job until the programmers can see what isnt geting recognized when the Beta SW addin gets loaded.

[v3n0m]

Try the instructions from this post.
viewtopic.php?t=4901

This isnt the solution just a patch job until the programmers can see what isnt geting recognized when the Beta SW addin gets loaded.

It works :D:D

Thanks so much.
Of course a "real" solution is always welcome, but for the time being, this should work just fine.

Thanks a lot,
Nick

[ldzwonka]

I install it after i use standard drivers. I common use solidworks. Unfortuanetly i cannot assign special buttons i SW.
What i see, that driver is much faster than the standard one... i hope You finished working on that drivers soon.
Now i working with newest standard drivers 3.15.2, waiting for 3dxWare 10 final

[nicolight]

Hi everybody.
I get some problems to use this software: My spacemouse pro is not reconnized.
I used before the 3DXsoftware 3.15.4. So I uninstall that one, restart computer, and install 3DxWare64SPP_v10-0-11_r1165. Restart again. Doesn't work.
I surched on the forum, you explained somewhere how to proceed to make clean uninstall. I did everything, install 3DxWare. I rich the same result.
In 3Dconnexion properties, in hardware information, your 3D Mouse: No device. I put a picture to show you.
What did I do wrong? Do yuo have any ideas?
Thanks for your help.

[jwick]

Hi everybody.
I get some problems to use this software: My spacemouse pro is not reconnized.
Thanks for your help.

The current beta does not support the Spacemouse Pro. There will be a beta that does support it shortly. Thank you for your patience.

[nicolight]

Thanks Jewick.
Could you tell me approximatly the delay for that update?

[jwick]

Thanks Jewick.
Could you tell me approximatly the delay for that update?

No, I can't. I will tell you it was supposed to be yesterday. So it should be soon.

[wavez]

Hi everybody,
I'm a new user of the Space navigator 3D mouse(i purchase it yesterday), I've installed the new release drivers " 3DxSoftware32_v3-15-5_r1270.exe" and all system seams works, after that I tried to install the 3DxWare 10 beta to use the Spacenavigator with conventional software (street view,internet explorer etc.) but the system did not accept the "3DxWare 10 beta" due to the new drivers released some days ago(3DxSoftware32_v3-15-5_r1270.exe).
Someone can help me to understand if the 3DxWare 10 beta is no more compatible with the new drivers or I do some mistakes during installation?
Thank you in advance for each answer,
Ciao, Wavez

[jwick]

Hi everybody,
I'm a new user of the Space navigator 3D mouse(i purchase it yesterday), I've installed the new release drivers " 3DxSoftware32_v3-15-5_r1270.exe" and all system seams works, after that I tried to install the 3DxWare 10 beta to use the Spacenavigator with conventional software (street view,internet explorer etc.) but the system did not accept the "3DxWare 10 beta" due to the new drivers released some days ago(3DxSoftware32_v3-15-5_r1270.exe).
Someone can help me to understand if the 3DxWare 10 beta is no more compatible with the new drivers or I do some mistakes during installation?
Thank you in advance for each answer,
Ciao, Wavez

3DxSoftware 3.15.5 and 3DxWare 10 are two different product lines. To install 3DxWare 10, uninstall 3DxSoftware 3.15.5 first. Then install 3DxWare 10 and ignore the check for the "newer version".

[jlrith]

Jwick,

What is the status on the new beta release?
"Supposed to be yesterday" is about to become "supposed to be last week."
Sure would be nice to use my expensive SpacepilotPro on more than 1 program.

[jwick]

Jwick,

What is the status on the new beta release?
"Supposed to be yesterday" is about to become "supposed to be last week."
Sure would be nice to use my expensive SpacepilotPro on more than 1 program.

It's left my hands--that's good. You don't need beta 12 for the SpacePilot PRO. It works fine with beta 11.

[wavez]

jwick wrote:
3DxSoftware 3.15.5 and 3DxWare 10 are two different product lines. To install 3DxWare 10, uninstall 3DxSoftware 3.15.5 first. Then install 3DxWare 10 and ignore the check for the "newer version".

Thank you for the answer jwick, I'll uninstall the 3DxSoftware and pass to 3DxWare...anyway, will it work with pro-engineer using the 3DxWare 10 drivers ? Are the supported programs like proE, AutoCad etc. not affected by the drivers?
Thank you for your patience
ciao, Wavez

[jwick]

jwick wrote:
3DxSoftware 3.15.5 and 3DxWare 10 are two different product lines. To install 3DxWare 10, uninstall 3DxSoftware 3.15.5 first. Then install 3DxWare 10 and ignore the check for the "newer version".

Thank you for the answer jwick, I'll uninstall the 3DxSoftware and pass to 3DxWare...anyway, will it work with pro-engineer using the 3DxWare 10 drivers ? Are the supported programs like proE, AutoCad etc. not affected by the drivers?
Thank you for your patience
ciao, Wavez

All the standard applications work in 3DxWare 10 beta 11. Most problems you may see are just errors in the profile (maybe a button is mapped to the wrong action). We have fixed quite a few of those in beta 12. The way the device responds to your input is different from 3DxSoftware and 3DxWare 10 beta 11. Beta 12 fixes that and, in our opinion, makes it better.

[jlrith]

1. Will you be opening a new post for beta 12 feedback?
2. The LEDs on the SpaceNavigator still light up when my computer goes to sleep, when the enable LED option is unchecked.

[jwick]

1. Will you be opening a new post for beta 12 feedback?

Use this topic for feedback on beta 12.

2. The LEDs on the SpaceNavigator still light up when my computer goes to sleep, when the enable LED option is unchecked.

Laptop or desktop? They go on when the machine goes to sleep (and stay on), or they go back on when the machine wakes?